+++ /dev/null
-.TH WIMLIB-IMAGEX "1" "March 2014" "@IMAGEX_PROGNAME@ @VERSION@" "User Commands"
-.SH NAME
-@IMAGEX_PROGNAME@-optimize \- Optimize a WIM archive
-.SH SYNOPSIS
-\fB@IMAGEX_PROGNAME@ optimize\fR \fIWIMFILE\fR [\fIOPTION\fR...]
-.SH DESCRIPTION
-\fB@IMAGEX_PROGNAME@ optimize\fR will rebuild the stand-alone WIM \fIWIMFILE\fR. The new
-WIM is written to a temporary file, and it is renamed to the original file when
-it's ready. This action will remove any holes that have been left as a result
-of appending images, so the new WIM may be slightly smaller than the old WIM.
-In addition, some errors in the original WIM may be fixed by re-writing it
-(although most cannot).
-This command is also available as simply \fBwimoptimize\fR if the appropriate
-hard link or batch file has been installed.
-.SH OPTIONS
-.TP 6
-\fB--check\fR
-When reading \fIWIMFILE\fR, verify its integrity if an integrity table is
-present. In addition, include an integrity table in the optimized WIM. If this
-option is not specified, by default the integrity table (if present) is not
-checked, and an integrity table is included in the rebuilt WIM if and only if
-one was present in the original WIM.
-.TP
-\fB--nocheck\fR
-Neither verify the integrity of \fIWIMFILE\fR using the integrity table, nor
-include an integrity table in the rebuilt WIM file.
-.TP
-\fB--recompress\fR
-Recompress all compressed streams in \fIWIMFILE\fR when rebuilding it. This
-will increase the time needed to rebuild the WIM, unless the WIM is
-uncompressed, but it may result in a better compression ratio if wimlib can do a
-better job than the program that wrote the original file. A side effect of this
-is that every stream in the original WIM will be checksummed, so this can help
-verify that the WIM is intact (equivalent to applying all the images from it).
-.IP ""
-Note: as of wimlib v1.5.3, wimlib's LZX compressor usually achieves the same or
-better compression than Microsoft's, but is slightly slower.
-.TP
-\fB--recompress-slow\fR, \fB--compress-slow\fR
-Spend even more time compressing the data in order to achieve a more optimal
-compression ratio. For LZX ("maximum") compression, compared to the default
-\fB--recompress\fR this will make compression about twice as slow and may
-improve the compression ratio by maybe 1%, depending on the data. For LZMS
-("recovery") compression this option also has an effect. For XPRESS ("fast")
-compression this option has no effect; however you may use \fB--compress\fR=LZX
-\fB--recompress-slow\fR to change the compression type to LZX and recompress
-slowly, as per this option. In any case, this option implies
-\fB--recompress\fR.
-.TP
-\fB--compress\fR=\fITYPE\fR
-Recompress the WIM file using the specified compression type. \fITYPE\fR may be
-"none", "fast" (or "XPRESS"), or "maximum" (or "LZX"). This implies
-\fB--recompress\fR.
-.IP ""
-\fITYPE\fR may also be "recovery" (or "LZMS"); however, this will result in
-reduced compatibility. See the documentation for this option to
-\fB@IMAGEX_PROGNAME@ capture\fR (1) for more details.
-.TP
-\fB--chunk-size\fR=\fISIZE\fR
-Set the WIM compression chunk size to \fISIZE\fR. See the documentation for
-this option to \fB@IMAGEX_PROGNAME@ capture\fR (1) for more details.
-.TP
-\fB--pack-streams\fR, \fB--solid\fR
-Create a "solid" archive that compresses multiple files together. This can
-result in a higher compression ratio, but has disadvantages such as reduced
-compatibility; see the documentation for this option to
-\fB@IMAGEX_PROGNAME@-capture\fR (1) for more details.
-.TP
-\fB--pack-chunk-size\fR=\fISIZE\fR, \fB--solid-chunk-size\fR=\fISIZE\fR
-Like \fB--chunk-size\fR, but set the chunk size used in packed resources.
-.TP
-\fB--threads\fR=\fINUM_THREADS\fR
-Number of threads to use for compressing data. Default: autodetect (number of
-processors). This parameter is only meaningful when \fB--recompress\fR is also
-specified.
-.TP
-\fB--pipable\fR
-Rebuild the WIM so that it can be applied fully sequentially, including from a
-pipe. See \fB@IMAGEX_PROGNAME@ capture\fR(1) for more details about creating
-pipable WIMs. By default, when neither \fB--pipable\fR or \fB--not-pipable\fR
-is specified, the rebuilt WIM will be pipable if and only if it was already
-pipable.
-.TP
-\fB--not-pipable\fR
-Rebuild the WIM in the non-pipable format. (This is the default if
-\fIWIMFILE\fR is not pipable.)
-.SH NOTES
-\fB@IMAGEX_PROGNAME@ optimize\fR does not support split WIMs.
-.PP
-\fB@IMAGEX_PROGNAME@ optimize\fR is roughly equivalent to:
-.RS
-.PP
-\fB@IMAGEX_PROGNAME@ export\fR \fIWIMFILE\fR all tmp.wim && mv tmp.wim \fIWIMFILE\fR
-.RE
-.PP
-.SH SEE ALSO
-.BR @IMAGEX_PROGNAME@ (1)
-.BR @IMAGEX_PROGNAME@-export (1)
git://wimlib.net / wimlib / blobdiff