+\fIDEST_WIMFILE\fR does not yet exist, since if \fIDEST_WIMFILE\fR exists, the
+compression type must be the same as that of \fIDEST_WIMFILE\fR.
+.IP ""
+\fITYPE\fR may be "none", "maximum", or "fast". By default, it is the same as
+that of the input WIM file.
+.IP ""
+You may also specify the actual names of the compression algorithms, "XPRESS"
+and "LZX", instead of "fast" and "maximum", respectively.
+.TP
+\fB--threads\fR=\fINUM_THREADS\fR
+Number of threads to use for compressing data. Default: autodetect (number of
+processors). Note: if exporting to an uncompressed WIM, or exporting to a WIM
+with the same compression type as the source WIM, additional threads will not
+be used, regardless of this parameter, since no data compression needs to be
+done in these cases.
+.TP
+\fB--rebuild\fR
+When exporting image(s) to an existing WIM: rebuild the entire WIM rather than
+appending data to the end of it. Rebuilding the WIM is slower, but will save a
+little bit of space that would otherwise be left as a hole in the WIM. Also see
+\fB@IMAGEX_PROGNAME@ optimize\fR.
+.TP
+\fB--ref\fR="\fIGLOB\fR"
+File glob of additional split WIM parts that are part of the split WIM being
+exported. See \fBSPLIT_WIMS\fR.
+.SH SPLIT WIMS
+You may use \fB@IMAGEX_PROGNAME@ export\fR to export images from a split WIM. The
+\fISRC_WIMFILE\fR argument is used to specify the first part of the split WIM, and
+the \fB--refs\fR="\fIGLOB\fR" option is used to provide a shell-style file glob
+that specifies the additional parts of the split WIM. \fIGLOB\fR is expected to
+be a single string on the command line, so \fIGLOB\fR must be quoted so that it
+is protected against shell expansion. \fIGLOB\fR must expand to all parts of
+the split WIM, except optionally the first part which may either omitted or
+included in the glob (but the first part MUST be specified as \fISRC_WIMFILE\fR as
+well).
+.PP
+Here's an example. The names for the split WIMs usually go something like:
+.PP
+.RS
+.nf
+mywim.swm
+mywim2.swm
+mywim3.swm
+mywim4.swm
+mywim5.swm
+.RE
+.PP
+To export the first image of this split WIM to a new or existing WIM file
+"other.wim", run:
+.PP
+.RS
+@IMAGEX_PROGNAME@ export mywim.swm 1 other.wim --ref="mywim*.swm"
+.RE
+.SH NOTES
+It is safe to abort an \fB@IMAGEX_PROGNAME@ export\fR command partway through;
+however, after doing this, it is recommended to run \fB@IMAGEX_PROGNAME@
+optimize\fR on the destination WIM to remove any data that was appended to the
+physical WIM file but not yet incorporated into the structure of the WIM, unless
+\fB--rebuild\fR was specified, in which case you should delete the temporary
+file left over.
+.SH EXAMPLES
+Export the second image of 'boot.wim' to the new WIM file 'new.wim', and
+change the compression type to maximum, if it wasn't maximum already:
+.RS
+.PP
+@IMAGEX_PROGNAME@ export boot.wim 2 new.wim --compress=maximum
+.RE
+.PP